思科交换机sn码在哪里（思科Catalyst37503560系列交换机上的PIM存根路由）

组播控制平面数据流由在LAN环境的每个路由器总是看到。Stub IP组播用于减少和最小化在接入层的LAN被看到的多余的组播数据流和保存在媒体的带宽转发组播数据流到上行分配/核心层。

在Catalyst 3750及3560系列交换机、PIM Stub组播功能支持组播路由在分布层之间和接入层中。它支持PIM接口的两种类型：上行链路PIM接口和PIM无源接口。特别是，配置的一个路由接口与PIM被动模式不通过/转发PIM控制层面流量;它只通过/转发IGMP流量。

尝试进行此配置之前，请确保满足以下要求：

1、PIM终端路由器不发送分布式路由器之间的中转流量。此行为由单播(EIGRP)残余部分路由强制执行。适当的单播残余部分路由配置是要求的协助此PIM终端路由器行为。PIM残余部分功能不防止配置RIP、静态路由或者PIM RP的路由器管理员绕过此限制。

2、已进行定向连接仅组播(IGMP)接收方和来源在第2层访问域允许。访问域不支持PIM协议。

3、不支持冗余的PIM终端路由器拓扑。

网络拓扑图：

网络拓扑图

配置：

1. 发出此命令启用组播路由全局在思科交换机或交换机堆叠：

mix_stack(config)#ip multicast-routing distributed

1. 发出此命令定义SSM范围与默认组范围的IP组播地址：

mix_stack(config)#ip pim ssm default

1. 发出此命令启用在上行链路的PIM SSM ：

mix_stack(config)#interface GigabitEthernet3/0/25 !--- By default switch configures the Layer 2 parameters. So in order to configure the Layer 3 parameter, use the next command. mix_stack(config-if)#no switchport mix_stack(config-if)#ip pim sparse-dense-mode

1. 发出此命令启用在VLAN接口的PIM残余部分路由：

mix_stack(config)#interface vlan100 mix_stack(config-if)#ip pim passive

交换(mix_stack)配置

mix_stack#show run Building configuration... Current configuration : 7810 bytes ! version 12.2 no service pad service timestamps debug uptime service timestamps log uptime no service password-encryption ! hostname mix_stack ! ! switch 2 provision ws-c3750e-24pd switch 3 provision ws-c3750g-24ts switch 5 provision ws-c3750-24fs switch 9 provision ws-c3750e-24pd ! ip routing ! ! ip multicast-routing distributed ! !--- Output suppressed. ! ! vlan 100 ! ! interface GigabitEthernet2/0/1 switchport access vlan 100 no keepalive spanning-tree portfast ! interface GigabitEthernet2/0/2 switchport access vlan 100 no keepalive spanning-tree portfast ! ! !--- Output suppressed. ! ! interface GigabitEthernet3/0/25 no switchport ip address 3.1.1.2 255.255.255.248 ip pim sparse-dense-mode ! ! !--- Output suppressed. ! ! interface GigabitEthernet9/0/24 no switchport ip address 10.1.1.1 255.255.255.0 ip pim passive no keepalive ! ! !--- Output suppressed. ! ! interface Vlan1 no ip address ! interface Vlan100 ip address 100.1.1.1 255.255.255.0 ip pim passive ! ! !--- Output suppressed. ! ! ip pim ssm default ! ! !--- Output suppressed. ! ! control-plane ! ! line con 0 exec-timeout 0 0 speed 115200 line vty 0 4 login line vty 5 15 login ! end

验证：

使用本部分可确认配置能否正常运行。

命令输出解释程序(OIT) 支持某些 show 命令。使用 OIT 可查看对 show 命令输出的分析。

发出show ip pim interface命令为了显示是每个接口的enable (event)的PIM Stub。

mix_stack#show ip pim interface Address Interface Ver/ Nbr Query DR DR Mode Count Intvl Prior 3.1.1.2 GigabitEthernet3/0/25 v2/SD 1 30 1 3.1.1.2 100.1.1.1 Vlan100 v2/P 0 30 1 100.1.1.1 10.1.1.1 GigabitEthernet9/0/24 v2/P 0 30 1 10.1.1.1

发出show ip igmp groups详细信息显示加入特定组播源/组的感兴趣客户端。

mix_stack#show ip igmp groups 232.0.0.9 det Flags: L - Local, U - User, SG - Static Group, VG - Virtual Group, SS - Static Source, VS - Virtual Source, Ac - Group accounted towards access control limit Interface: GigabitEthernet9/0/24 Group: 232.0.0.9 Flags: SSM Uptime: 00:00:10 Group mode: INCLUDE Last reporter: 10.1.1.2 CSR Grp Exp: 00:02:57 Group source list: (C - Cisco Src Report, U - URD, R - Remote, S - Static, V - Virtual, M - SSM Mapping, L - Local, Ac - Channel accounted towards access control limit) Source Address Uptime v3 Exp CSR Exp Fwd Flags 200.1.1.3 00:00:10 stopped 00:02:57 Yes CM Interface: Vlan100 Group: 232.0.0.9 Flags: SSM Uptime: 01:42:08 Group mode: INCLUDE Last reporter: 100.1.1.3 CSR Grp Exp: 00:02:00 Group source list: (C - Cisco Src Report, U - URD, R - Remote, S - Static, V - Virtual, M - SSM Mapping, L - Local, Ac - Channel accounted towards access control limit) Source Address Uptime v3 Exp CSR Exp Fwd Flags 200.1.1.3 01:42:12 stopped 00:02:00 Yes CM mix_stack#

发出show ip mroute验证组播流从来源转发给感兴趣客户端。

mix_stack#show ip mroute 232.0.0.9 IP Multicast Routing Table Flags: D - Dense, S - Sparse, B - Bidir Group, s - SSM Group, C - Connected, L - Local, P - Pruned, R - RP-bit set, F - Register flag, T - SPT-bit set, J - Join SPT, M - MSDP created entry, X - Proxy Join Timer Running, A - Candidate for MSDP Advertisement, U - URD, I - Received Source Specific Host Report, Z - Multicast Tunnel, z - MDT-data group sender, Y - Joined MDT-data group, y - Sending to MDT-data group V - RD & Vector, v - Vector Outgoing interface flags: H - Hardware switched, A - Assert winner Timers: Uptime/Expires Interface state: Interface, Next-Hop or VCD, State/Mode (200.1.1.3, 232.0.0.9), 01:44:23/00:02:52, flags: sTI Incoming interface: GigabitEthernet3/0/25, RPF nbr 3.1.1.1 Outgoing interface list: GigabitEthernet9/0/24, Forward/Sparse-Dense, 00:02:24/00:02:50 Vlan100, Forward/Sparse-Dense, 01:44:23/00:02:52