模具英语单词怎么说(关于模具的英语大全)

一、入水:gate 进入位: gate location ,今天小编就来聊一聊关于模具英语单词怎么说?接下来我们就一起去研究一下吧!

模具英语单词怎么说(关于模具的英语大全)

模具英语单词怎么说

一、入水:gate

进入位: gate location

水口形式:gate type

大水口:edge gate

细水口: pin-point gate

水口大小:gate size

转水口: switching runner/gate

唧嘴口径: sprue diameter

二、流道: runner

热流道: hot runner,hot manifold

热嘴冷流道: hot sprue/cold runner

唧嘴直流: direct sprue gate

圆形流道:round(full/half runner

流道电脑分析:mold flow analysis

流道平衡:runner balance

热嘴: hot sprue

热流道板:hot manifold

发热管:cartridge heater

探针: thermocouples

插头: connector plug

插座: connector socket

密封/封料: seal

三、运水:water line

喉塞:line lpug

喉管:tube

塑胶管:plastic tube

快速接头:jiffy quick connector plug/socker

四、模具零件: mold components

三板模:3-plate mold

二板模:2-plate mold

边钉/导边:leader pin/guide pin

边司/导套:bushing/guide bushing

中托司:shoulder guide bushing

中托边L:guide pin

顶针板:ejector retainner plate

托板: support plate

螺丝: screw

管钉:dowel pin

开模槽:ply bar scot

内模管位:core/cavity inter-lock

顶针: ejector pin

司筒:ejector sleeve

司筒针:ejector pin

推板:stripper plate

缩呵:movable core,return core core puller

扣机(尼龙拉勾):nylon latch lock

斜顶:lifter

模胚(架): mold base

上内模:cavity insert

下内模:core insert

行位(滑块): slide

镶件:insert

压座/斜鸡:wedge

耐磨板/油板:wedge wear plate

压条:plate

撑头: support pillar

唧嘴: sprue bushing

挡板:stop plate

定位圈:locating ring

锁扣:latch

扣鸡:parting lock set

推杆:push bar

栓打螺丝:S.H.S.B

顶板:eracuretun

活动臂:lever arm

分流锥:spure sperader

水口司:bush

垃圾钉:stop pin

隔片:buffle

弹弓柱:spring rod

弹弓:die spring

中托司:ejector guide bush

中托边:ejector guide pin

镶针:pin

销子:dowel pin

波子弹弓:ball catch

喉塞: pipe plug

锁模块:lock plate

斜顶:angle from pin

斜顶杆:angle ejector rod

尼龙拉勾:parting locks

活动臂:lever arm

复位键、提前回杆:early return bar

气阀:valves

斜导边:angle pin

术语:terms

承压平面平衡:parting surface support balance

模排气:parting line venting

回针碰料位:return pin and cavity interference

模总高超出啤机规格:mold base shut hight

顶针碰运水:water line interferes withejector pin

料位出上/下模:part from cavith (core) side

模胚原身出料位:cavity direct cut on A-plate,core direct cut onB-plate.

不准用镶件: Do not use (core/cavity) insert

用铍铜做镶件: use beryllium copper insert

初步(正式)模图设计:preliinary (final) mold design

反呵:reverse core

弹弓压缩量:spring compressed length

稳定性好:good stability,stable

强度不够:insufficient rigidity

均匀冷却:even cooling

扣模:sticking

热膨胀:thero expansion

公差:tolorance

铜公(电极):copperelectrod

英文简称 英文全称 中文全称

ABA Acrylonitrile-butadiene-acrylate 丙烯腈/丁二烯/丙烯酸酯共聚物

ABS Acrylonitrile-butadiene-styrene 丙烯腈/丁二烯/苯乙烯共聚物

AES Acrylonitrile-ethylene-styrene 丙烯腈/乙烯/苯乙烯共聚物

AMMA Acrylonitrile/methyl Methacrylate 丙烯腈/甲基丙烯酸甲酯共聚物

ARP Aromaticpolyester 聚芳香酯

AS Acrylonitrile-styrene resin 丙烯腈-苯乙烯树脂

ASA Acrylonitrile-styrene-acrylate 丙烯腈/苯乙烯/丙烯酸酯共聚物

CA Celluloseacetate 醋酸纤维塑料

CAB Cellulose acetate butyrate 醋酸-丁酸纤维素塑料

CAP Cellulose acetate propionate 醋酸-丙酸纤维素

CE Cellulose plastics, general 通用纤维素塑料

CF Cresol-formaldehyde 甲酚-甲醛树脂

CMC Carboxymethylcellulose 羧甲基纤维素

CN Cellulosenitrate 硝酸纤维素

CP Cellulosepropionate 丙酸纤维素

CPE Chlorinatedpolyethylene 氯化聚乙烯

CPVC Chlorinated poly(vinyl chloride) 氯化聚氯乙烯

CS Casein 酪蛋白

CTA Cellulosetriacetate 三醋酸纤维素

EC Ethylcellulose 乙烷纤维素

EMA Ethylene/methacrylicacid 乙烯/甲基丙烯酸共聚物

EP Epoxy,epoxide 环氧树脂

EPD Ethylene-propylene-diene 乙烯-丙烯-二烯三元共聚物

EPM Ethylene-propylene polymer 乙烯-丙烯共聚物

EPS Expandedpolystyrene 发泡聚苯乙烯

ETFE Ethylene-tetrafluoroethylene 乙烯-四氟乙烯共聚物

EVA Ethylene/vinylacetate 乙烯-醋酸乙烯共聚物

EVAL Ethylene-vinylalcohol 乙烯-乙烯醇共聚物

FEP Perfluoro(ethylene-propylene) 全氟(乙烯-丙烯)塑料

FF Furanformaldehyde 呋喃甲醛

HDPE High-density polyethylene plastics高密度聚乙烯塑料

HIPS High impactpolystyrene 高冲聚苯乙烯

IPS Impact-resistant polystyrene 耐冲击聚苯乙烯

LCP Liquid crystalpolymer 液晶聚合物

LDPE Low-density polyethylene plastics 低密度聚乙烯塑料

LLDPE Linear low-density polyethylene 线性低密聚乙烯

LMDPE Linear medium-density polyethylene 线性中密聚乙烯

MBS Methacrylate-butadiene-styrene 甲基丙烯酸-丁二烯-苯乙烯共聚物

MDPE Medium-density polyethylene 中密聚乙烯

MF Melamine-formaldehyde resin 密胺-甲醛树脂

MPF Melamine/phenol-formaldehyde 密胺/酚醛树脂

英文简称 英文全称 中文全称

PA Polyamide(nylon) 聚酰胺(尼龙)

PAA Poly(acrylic acid) 聚丙烯酸

PADC Poly(allyl diglycol carbonate) 碳酸-二乙二醇酯· 烯丙醇酯树脂

PAE Polyarylether 聚芳醚

PAEK Polyaryletherketone 聚芳醚酮

PAI Polyamide-imide 聚酰胺-酰亚胺

PAK Polyester alkyd 聚酯树脂

PAN Polyacrylonitrile 聚丙烯腈

PARA Polyaryl amide 聚芳酰胺

PASU Polyarylsulfone 聚芳砜

PAT Polyarylate 聚芳酯

PAUR Poly(ester urethane) 聚酯型聚氨酯

PB Polybutene-1 聚丁烯-[1]

PBA Poly(butyl acrylate) 聚丙烯酸丁酯

PBAN Polybutadiene-acrylonitrile 聚丁二烯-丙烯腈

PBS Polybutadiene-styrene 聚丁二烯-苯乙烯

PBT Poly(butylene terephthalate) 聚对苯二酸丁二酯

PC Polycarbonate 聚碳酸酯

PCTFE Polychlorotrifluoroethylene 聚氯三氟乙烯

PDAP Poly(diallyl phthalate) 聚对苯二甲酸二烯丙酯

PE Polyethylene 聚乙烯

PEBA Polyether block amide 聚醚嵌段酰胺

PEBA Thermoplastic elastomer polyether 聚酯热塑弹性体

PEEK Polyetheretherketone 聚醚醚酮

PEI Poly(etherimide) 聚醚酰亚胺

PEK Polyether ketone 聚醚酮

PEO Poly(ethylene oxide) 聚环氧乙烷

PES Poly(ether sulfone) 聚醚砜

PET Poly(ethylene terephthalate) 聚对苯二甲酸乙二酯

PETG Poly(ethylene terephthalate) glycol 二醇类改性PET

PEUR Poly(ether urethane) 聚醚型聚氨酯

PF Phenol-formaldehyde resin 酚醛树脂

PFA Perfluoro(alkoxy alkane) 全氟烷氧基树脂

PFF Phenol-furfural resin 酚呋喃树脂

PI Polyimide 聚酰亚胺

PIB Polyisobutylene 聚异丁烯

PISU Polyimidesulfone 聚酰亚胺砜

PMCA Poly(methyl-alpha-chloroacrylate) 聚α-氯代丙烯酸甲酯

PMMA Poly(methyl methacrylate) 聚甲基丙烯酸甲酯

PMP Poly(4-methylpentene-1) 聚4-甲基戊烯-1

PMS Poly(alpha-methylstyrene) 聚α-甲基苯乙烯

POM Polyoxymethylene, polyacetal 聚甲醛

PP Polypropylene 聚丙烯

PPA Polyphthalamide 聚邻苯二甲酰胺

PPE Poly(phenylene ether) 聚苯醚

PPO Poly(phenylene oxide) deprecated 聚苯醚

PPOX Poly(propylene oxide) 聚环氧(丙)烷

PPS Poly(phenylene sulfide) 聚苯硫醚

PPSU Poly(phenylene sulfone) 聚苯砜

PS Polystyrene 聚苯乙烯

PSU Polysulfone 聚砜

PTFE Polytetrafluoroethylene 聚四氟乙烯

PUR Polyurethane 聚氨酯

PVAC Poly(vinyl acetate) 聚醋酸乙烯

PVAL Poly(vinyl alcohol) 聚乙烯醇

PVB Poly(vinyl butyral) 聚乙烯醇缩丁醛

PVC Poly(vinyl chloride) 聚氯乙烯

PVCA Poly(vinyl chloride-acetate) 聚氯乙烯醋酸乙烯酯

PVDC Poly(vinylidene chloride) 聚(偏二氯乙烯)

PVDF Poly(vinylidene fluoride) 聚(偏二氟乙烯)

PVF Poly(vinyl fluoride) 聚氟乙烯

PVFM Poly(vinyl formal) 聚乙烯醇缩甲醛

PVK Polyvinylcarbazole 聚乙烯咔唑

PVP Polyvinylpyrrolidone 聚乙烯吡咯烷酮

S/MA Styrene-maleic anhydride plastic 苯乙烯-马来酐塑料

SAN Styrene-acrylonitrile plastic 苯乙烯-丙烯腈塑料

SB Styrene-butadiene plastic 苯乙烯-丁二烯塑料

Si Silicone plastics 有机硅塑料

SMS Styrene/alpha-methylstyrene plastic 苯乙烯-α-甲基苯乙烯塑料

SP Saturated polyester plastic 饱和聚酯塑料

SRP Styrene-rubber plastics 聚苯乙烯橡胶改性塑料

TEEE Thermoplastic Elastomer,Ether-Ester 醚酯型热塑弹性体

TEO Thermoplastic Elastomer, Olefinic 聚烯烃热塑弹性体

TES Thermoplastic Elastomer, Styrenic 苯乙烯热塑性弹性体

TPEL Thermoplastic elastomer 热塑(性)弹性体

TPES Thermoplastic polyester 热塑性聚酯

TPUR Thermoplastic polyurethane 热塑性聚氨酯

TSUR Thermoset polyurethane 热固聚氨酯

UF Urea-formaldehyde resin 脲甲醛树脂

UHMWPE Ultra-high molecular weight PE 超高分子量聚乙烯

UP Unsaturated polyester 不饱和聚酯

VCE Vinyl chloride-ethylene resin 氯乙烯/乙烯树脂

VCEV Vinyl chloride-ethylene-vinyl 氯乙烯/乙烯/醋酸乙烯共聚物

VCMA Vinyl chloride-methyl acrylate 氯乙烯/丙烯酸甲酯共聚物

VCMMA Vinyl chloride-methylmethacrylate 氯乙烯/甲基丙烯酸甲酯共聚物

VCOA Vinyl chloride-octyl acrylate resin 氯乙烯/丙烯酸辛酯树脂

VCVAC Vinyl chloride-vinyl acetate resin 氯乙烯/醋酸乙烯树脂

VCVDC Vinyl chloride-vinylidene chloride 氯乙烯/偏氯乙烯共聚物

,

免责声明:本文仅代表文章作者的个人观点,与本站无关。其原创性、真实性以及文中陈述文字和内容未经本站证实,对本文以及其中全部或者部分内容文字的真实性、完整性和原创性本站不作任何保证或承诺,请读者仅作参考,并自行核实相关内容。文章投诉邮箱:anhduc.ph@yahoo.com

    分享
    投诉
    首页